Iphone 7 Screw Size Chart

July 09, 2024 Post a Comment

Iphone 7 screw size chart

Power off your iPhone before beginning disassembly. Remove the two 3.4 mm pentalobe screws on the bottom edge of the iPhone.

What size is an iPhone screw?

Pentalobe screw sizes include TS1 (0.8 mm, used on every iPhone starting with the iPhone 4), TS4 (1.2 mm, used on the MacBook Air and the MacBook Pro with Retina display), and TS5 (1.5 mm, used on the 2009 MacBook Pro battery).

What screws are at the bottom of an iPhone 7?

Description. All iPhone 7 and 7 Plus phones have two proprietary 5-point pentalobe screws near the lightning connector to keep anyone other than an Apple technician from opening the phone. Replace the screws in the bottom exterior of your smartphone. These screws are compatible with an iPhone 7 or 7 Plus.

How many screws does an iPhone 7 have?

Replace the 2 screws in the bottom exterior of your phone. Compatible with an iPhone 6s, iPhone 6s Plus, iPhone 7, or iPhone 7 Plus.

What tools do I need to open iPhone 7?

The necessary tools and screwdrivers for disassembling the iPhone 7:

Three-winglets screwdriver (Tri-Wing Y0) – 0,6mm.
Screwdriver five-star – 0,8mm.
Phillips screwdriver – PH00 1.5mm.
Suction cup for removing touchscreens.
Plastic mediator.
Hairdryer.
Waterproof Adhesive Tape.

What screw size is #7?

Size	Major Thread Diameter*
Size	Decimal	Nearest Fractional Measurement
#6	.138"	9/64"
#7	.151"	5/32"
#8	.164"	5/32"

How do I know what size my screw is?

To measure the diameter of screws and bolts, you measure the distance from the outer thread on one side to the outer thread on the other side. This is called the major diameter and will usually be the proper size of the bolt.

Is P5 and T5 screwdriver the same?

❤ 5 point (P5) screwdriver is used for opening the back panel screws. ❤ 6 point (T5) screwdriver is used for taking off the battery and fan screws. ❤ Tweezers for fixing small parts and taking out the electronic components of the narrow place.

What size screw is 38mm?

#10 38mm (1 1/2") Screw.

What screws does the iPhone 7 Plus use?

Power off your iPhone before beginning disassembly. Remove the two 3.4 mm pentalobe screws at the bottom edge of the iPhone.

What are the holes on back of iphone7?

The user guide identifies these as the camera, microphone, and camera flash.

How do I remove a screw from an iPhone 7?

Put your screwdriver into the hole. And then just hold it. And then push down so you want to push

How do you remove iPhone 7 Tri screws without a screwdriver?

And any knife with a sharp tip should work with for this so you could use like a stanley knife or a

Are all iPhone 7 the same size?

The iPhone 7, 8, and SE (2020) are the same size. These model iPhones have a 4.7" screen (diagonally measured as shown above). These two models are different than the iPhone 6/6s model Apple offers due to no longer having a headphone jack and a different camera design.

What inch size is iPhone 7?

As with prior models, iPhone 7 is available in two sizes: one with a 4.7 in (120 mm) screen, and a "Plus" variant with a 5.5 in (140 mm) screen.

How do I take the back off my iPhone 7?

Insert the flat edge of a spudger into the bottom right corner of the device. Twist the spudger to widen the gap between the display assembly and the rear case. Slide the flat end of the spudger up the right side of the phone to break up the adhesive holding the display in place.